Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and steering of the car
10.3. Check of a state and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability
10:10. Replacement of stupichny bearings
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10:12. Removal and installation of components and assembly of a back suspension bracket
10:13. Removal, check of a state and installation of levers of a back suspension bracket
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket
10:15. Removal and installation of shock-absorbers of a back suspension bracket
10:16. Removal and installation of the back stabilizer of cross stability
10:17. Removal, check of a state and installation of a cross jet bar of a back suspension bracket
10:18. Pumping of a hydraulic path of the steering drive
10:19. Checks and adjustments of a steering wheel
10:20. Check of effort of resistance to sliding of a lath of the steering mechanism
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
10:22. Check of hydraulic pressure of GUR
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump
10:24. Removal and installation of reduktorny assembly
10:25. Removal and installation of assembly of the steering mechanism
10:26. Removal and installation of the steering pump
10:27. Removal and installation of a steering wheel
10:28. Removal and installation of assembly of the combined understeering switches
10:29. Removal and installation of the lock of ignition / blocking of a steering column
10:30. Removal, check of a state and installation of a steering column
10:31. Angles of installation of forward wheels
11. Body
12. Electric equipment
 














10-27-snyatie-i-ustanovka-rulevogo-kolesa.html

10:27. Removal and installation of a steering wheel

The cars considered in the present manual are equipped with system of additional safety of SRS better known as a safety cushion. Before performing any works near assembly of a pillow or a steering column, without fail disconnect system in order to avoid getting injured as a result of its casual operation (see the Head Elektrooborudovaniye). Isolation and contact sockets of an electrical wiring of a chain of SRS are painted in bright yellow color. It is not necessary to connect any diagnostic units to this chain!


Removal

Bolts of fastening of the module of a safety cushion are put on special sealant and are not subject to reuse.


 PERFORMANCE ORDER

  1. Before starting removal of a steering wheel, deactivate SRS (see the Head Elektrooborudovaniye).
  2. Remove the lower cover of a casing of a steering column.
  3. Disconnect an electrical wiring from the module of a driver's frontal safety cushion, then remove the left and right sections of a casing.
  1. By means of a key like TORX turn out bolts of fastening of the module (see the prevention).
  1. Remove a safety cushion and the spiral cable reel. Transfer assembly to a workbench and lay it a slip up.
  2. Bring forward wheels of the car into rectilinear situation.
  3. Disconnect a horn electrical wiring, and also all other electrical wiring preventing removal of a steering wheel.
  4. Give a nut of fastening of a steering wheel, remove a washer and mark the provision of a wheel concerning a shaft of a steering column.
  1. By means of a special stripper remove a steering wheel and disconnect a cable of the drive of blocking of switching of AT.

Do not draw a stripper bolt! Do not make attempts of knocking down of a steering wheel by means of the hammer!


Installation

 PERFORMANCE ORDER

  1. Make sure that forward wheels still are in rectilinear situation.
  2. Check correctness of combination of a uvula of the sensor switch of the returnable device of the switch of indexes of turn with reciprocal risky the understeering switch.
  1. Make sure that the spiral SRS cable reel is in neutral (central) situation, and adjusting tags correctly are combined.

At the wrong installation the cable reel can be jammed at strong deployment of a steering wheel!

  1. Install the reel on a steering column. In case of need make centering of a drum for what turn it on 2.5 turns from extreme situation and achieve combination of adjusting tags. For reliability temporarily fix a drum in neutral situation by means of an adhesive tape.
  1. Connect an electrical wiring to the cable reel.
  2. Connect a cable of blocking of switching of AT.
  3. Establish a casing of a steering column and remove the adhesive tape fixing the cable reel.
  4. Establish a steering wheel — track correctness of hit of the directing pin of the cable reel in reciprocal nests.
  5. Pass the cable reel throughout a wheel nave.
  6. Connect a horn electrical wiring, then enter the cable reel into gearing with ratchet doggies of a steering wheel.
  7. Tighten a nut of fastening of a steering wheel with the required effort.
  8. Install into place the safety cushion module, screw NEW fixing bolts and tighten them with the required effort.
  9. Establish into place the remained elements of a casing of a steering column.
  10. In conclusion make SRS activation (see the Head Elektrooborudovaniye).


"on the page back
10:26. Removal and installation of the steering pump
on the following page"
10:28. Removal and installation of assembly of the combined understeering switches