|
2-5-10-pravila-polzovaniya-sistemojj-upravleniya-skorostyu-tempostatom.html
2.5.10. Instructions for use control system of speed (tempostaty) At refusals of a tempostat (ASCD) there is an automatic shutdown of system, the followed blinking of a control lamp of a tempostat on an instrument guard of the car (see the car Equipment, an arrangement of devices and governing bodies).
If the control lamp of a tempostat begins to blink, make switching off of system from the main switch and drive away the car on car repair shop.
Can lead inclusion of a tempostat from the main switch at a simultaneous nazhimaniye on buttons of management of the RES/ACCEL, COAST/SET or CANCEL system of the control panel on a steering wheel to a blinking of a control lamp, activation of system has to be made according to the instructions given below.
|
|
It is not necessary to use темпостат in the following road conditions:
- When there is no possibility of the movement with the chosen constant speed;
- At movement along the loaded roads;
- At the movement on the serpentine;
- In hilly and mountain areas;
- At a slippery paving;
- At strong wind.
Violation of this prevention is fraught with loss of control over management!
|
Management of functioning of a tempostat
Management of functioning of a tempostat
The control system of speed (темпостат) provides a possibility of automatic maintenance of speed of the movement of the car in the range from 48 to 144 km/h without use of the accelerator pedal.
For commission of overtaking squeeze out the accelerator pedal. After the pedal is released, the car will return to the chosen earlier cruiser speed.
At the movement under a bias or uphill темпостат does not provide maintenance of cruiser speed of the movement of the car and it has to be switched off.
Cancellation of the chosen cruiser speed can be made in three various ways:
- Press the CANCEL button (Cancellation) — the control lamp of a tempostat has to go out;
- Slightly squeeze out a pedal of a foot brake — the control lamp of a tempostat has to go out;
- Use the main switch of a tempostat — the control lamp of a tempostat, and also the control lamp which is built in a switch key have to go out.
After squeezing of a pedal of a foot brake at at the same time pressed RES/ACCEL button on the control panel, it is necessary to disconnect темпостат the main switch and to activate it repeatedly after a set of the required speed of the movement.
Tempostat is disconnected automatically at reduction in the rate of the movement of the car of the more than 13 km/h lower chosen cruiser value.
|
|
Switching off of a control system of speed can be made also by squeezing of a pedal of coupling (model with RKPP) or moving of the lever of the selector to situation "N" (models with AT) — the control lamp of a tempostat on an instrument guard has to go out. |
Increase in the chosen cruiser speed of the movement of the car can be made in three ways:
For decrease in cruiser speed:
- Slightly press a pedal of a foot brake — when the speed of the movement of the car decreases to the required value, press the COAST/SET button;
- Press the COAST/SET button and hold it pressed until the car does not slow down to the required speed;
- Short-term pressing the COAST/SET button it is possible to make step decrease in value of cruiser speed of the car with a step of 1.6 km/h.
For return to earlier chosen cruiser speed quickly press the RES button (see the illustration Management of Functioning of a Tempostat) — as soon as the car accelerates over 48 km/h, темпостат will automatically bring it to the chosen earlier cruiser speed of the movement which will support further.
Adjustment of a cable of the drive of a butterfly valve of a tempostat
Adjustment of a cable of the drive of a tempostat
|
|
Try not to allow twistings of a driving cable of ASCD!
At adjustment on pull a cable with excessive effort! |
|