|
|
|
|
8-3-5-snyatie-obsluzhivanie-i-ustanovka-maslyanogo-nasosa.html
8.3.5. Removal, service and installation of the oil pump
Design of a power shaft of a forward axis
Removal
|
|
- Remove a protective cover of a nave from a wheel which power shaft needs service. Remove a lock ring of fastening of a power shaft. Release nuts of fastening of a wheel.
- Car front also establish to Poddomkratta it on props and remove a wheel (see the illustration Scheme of an Institution of Props for fixing of the car in the lifted situation). Release a nut and bolts of fastening of cross draft.
- Slightly tapping with the hammer with soft (brass) brisk, beat out a power shaft from assembly of a rotary fist if the shaft does not give in, use a stripper.
- From the inside of a shaft turn out bolts of fastening of the sliding shaft hinge casing to a side flange.
- Having pulled, separate a shaft from a side flange of the main transfer.
|
|
Dismantling
|
|
- Slightly tapping at the edges of the sliding hinge casing, remove its sealing face cover. Shoot bandage films (collars) of fastening of protective covers.
- Mark adjusting position of the holder (crosspiece) of the hinge of rather sliding casing and a pin of a power shaft.
- Remove a lock ring from a shaft pin, then by means of a suitable press remove a hinge crosspiece.
- Remove a casing of the sliding flange and protective covers.
- Mark the adjusting provision of assembly of the external hinge and accurately separate the last from a shaft pin, having used for this purpose the hammer with sliding brisk and a suitable stripper.
|
|
Check
|
|
- Carefully wash out shaft components in solvent and dry with use of compressed air.
- Examine components on existence of signs of deformation and damages. Replace defective units.
- In case of identification of cracks or signs of twisting replace a bar of a power shaft.
- Estimate a condition of protective covers of CV JOINTS, in case of need make replacement.
|
|
Authors of the present manual recommend to replace protective covers regardless of their state. Prepare new bandage tapes of fastening of protective covers. |
- In case of detection of defects of the sliding casing of the internal CV JOINT it is subject to replacement complete with the hinge (assembly of a crosspiece). The external CV JOINT is not subject to dismantling and recovery repair and in case of failure is replaced assembled.
|
|
Assembly
Internal CV JOINT
|
|
- Wind the parts of a shaft equipped with notches with an insulating tape for protection new protective covers from damage.
- Put a protective cover of the CV JOINT and fix it on a shaft by a new bandage tape.
- Establish the sliding casing of hinged assembly.
- Establish the CV JOINT crosspiece — having tracked correctness of combination of the landing tags put in the course of dismantle, densely put a crosspiece the party equipped with a facet inside.
- Establish a new lock ring.
- Fill in hinged assembly 95 — 105 grams of lubricant from a remnabor, then establish a new sealing face cover.
- Pull a cover on a casing (edges of a cover have to get to reception flutes on a shaft and a hinge casing) and fix it by a new bandage tape — track that the cover was not overwound. The cover stretches on a hinge casing so that its full length made 95 — 97 mm.
|
|
External CV JOINT
|
|
- Put a protective cover of the CV JOINT and fix it on a shaft by a new bandage tape.
- Wind the parts of a shaft equipped with notches with an insulating tape for protection new protective covers from damage.
- Begin to knock hinged assembly on a shaft pin — track correctness of combination of the landing tags put in the course of dismantle. Establish a new lock ring.
- Fill in the hinge 135 — 145 grams of lubricant from a remnabor, then pull a cover on the CV JOINT and fix by a new bandage tape — the full length of a cover has to make 96 — 98 mm.
|
|
Installation Installation is made as it should be, the return to an order of dismantle of components. Track correctness of tightening of fixture.
|
|
|