Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
4.1. Specifications
4.2. Check of compression pressure in cylinders
4.3. Diagnostics of a condition of the engine with use of the vacuum gage
4.4. Removal and installation of the engine
4.5. Removal and installation of the inlet pipeline
4.6. Replacement of a belt of the GRM drive
4.7. Removal, check of a state and installation of a head of cylinders
4.8. Replacement of a forward epiploon of a bent shaft
4.9. Removal, check of a state and installation of components of the valvate mechanism
4.10. Replacement of epiploons of camshafts
4.11. Replacement of a back epiploon of a bent shaft
4.12. Removal and installation of the pallet of a case
4.13. Removal, service and installation of the oil pump
4.14. Alternative versions of schemes of recovery repair of the engine
4.15. An order of dismantling of the engine by preparation it to capital repairs
4.16. Dismantling and check of a condition of a head of cylinders and components of the valvate mechanism
4.17. Recommendations about service of valves
4.18. Assembly of a head of cylinders
4.19. Removal of conrod and piston assemblies
4.20. Removal of a bent shaft
4.21. Cleaning of the block of the engine
4.22. Check of a condition of the block of the engine
4.23. Honingovaniye of mirrors of cylinders
4.24. Check of a condition of components of conrod and piston group
4.25. Check of a condition of a bent shaft
4.26. Check of a state and selection of inserts of radical and conrod bearings of a bent shaft
4.27. Engine assembly order
4.28. Installation of piston rings
4.29. Installation of a bent shaft and check of working gaps of radical bearings
4.30. Installation of conrod and piston assemblies and check of size of working gaps in conrod bearings of a bent shaft
4.31. Trial start and a running in of the engine after capital repairs
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
11. Body
12. Electric equipment
 














4-5-snyatie-i-ustanovka-vpusknogo-truboprovoda.html

4.5. Removal and installation of the inlet pipeline

 PERFORMANCE ORDER

  1. Dump pressure in a power supply system (see Check of compression pressure in cylinders).
  2. Empty the cooling system (see the Head Routine maintenance).
  3. Disconnect cables of the drive of a butterfly valve and a tempostat from a collector of the inlet pipeline.
  4. Remove an air duct sleeve.
  5. Remove the lines of communication interfering access to the inlet pipeline:
    • Electrical wiring of the IACV-AAC valve, sensor of provision of a butterfly valve (TPS), sensor switch of extreme provisions of a butterfly valve, coil of ignition, powerful transistor, electromagnetic EGRC valve and sensor of temperature of EGR;
    • The hoses of a cooling path brought to a collector;
    • Hoses of a heating path;
    • PCV hose (from the right head of cylinders);
    • Vacuum hoses of a coal adsorber, GTTs and regulator of pressure;
    • Hose of a purge of a coal adsorber;
    • EGR tube;
    • Grounding tires;
  6. Turn out fixing bolts and remove a collector of the inlet pipeline with sealing laying.
  1. Disconnect the giving and returnable fuel pipes from the fuel highway, disconnect an electrical wiring from all injectors and remove the fuel highway.
  1. Working in strictly certain order, release bolts of fastening of the inlet pipeline.

  1. Finally turn out fixing bolts and remove the pipeline.
  2. In case of need remove the throttle case from a collector of the inlet pipeline.


Installation

Installation is made as it should be, the return to an order of dismantle of components — do not forget to make replacement of all sealing and insulating elements. Track that all fixture was tightened with the required effort.

Tightening of bolts of fastening of the inlet pipeline is made evenly as it should be, the return to an order of their easing.



"on the page back
4.4. Removal and installation of the engine
on the following page"
4.6. Replacement of a belt of the GRM drive