Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
9.1. Specifications
9.2. System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
9.3. Check of a state and replacement of brake lines and hoses
9.4. Replacement of blocks of disk brake mechanisms of forward wheels
9.5. Removal and installation of a support of the disk brake mechanism
9.6. Removal and installation of a brake disk
9.7. Replacement of brake boots of drum brake mechanisms of back wheels
9.8. Removal and installation of the main brake cylinder (MBC)
9.9. Removal and installation of assembly of the vacuum amplifier of brakes
9.10. Pumping of the brake system
9.11. Adjustment of the drive of the parking brake
9.12. Adjustments of a pedal of a foot brake
9.13. Adjustment of a spring of the valve regulator (LSV), sensitive to loading
9.14. Adjustment of sensors switches of stoplights and tempostata
9.15. Removal and installation of the ABS hydromodulator
9.16. Removal and installation of the G-sensor
9.17. Check of serviceability of functioning of wheel ABS sensors
9.18. Check of serviceability of functioning of the G-sensor
9.19. Check of serviceability of functioning of the relay of a driving electric motor of the hydromodulator
9.20. Check of serviceability of functioning of the relay of the electromagnetic valve of the hydraulic ABS modulator
10. Suspension bracket and steering
11. Body
12. Electric equipment
 














9-12-regulirovki-pedali-nozhnogo-tormoza.html

9.12. Adjustments of a pedal of a foot brake


Adjusting parameters of a pedal of a foot brake

And — Size of a free wheeling of a pedal
D — Height of provision of the squeezed-out pedal
N — Height of provision of the released pedal

With 1 — the Gap of the sensor switch of stoplights
With 2 — the Gap of the sensor switch of a tempostat


Free wheeling of a pedal

The size of a free wheeling of a pedal of a foot brake "And" (see an illustration Adjusting parameters of a pedal of a foot brake) has to make 4 — 12 mm.

 PERFORMANCE ORDER

  1. In case of need release a lock-nut and make necessary adjustment by rotation of a rod of a pusher of the vacuum amplifier of brakes around a cutting finger. Having achieved the required result, tighten a lock-nut with the required effort (12 — 15 Nanometers). Check serviceability of shutdown of stoplights at a pedal otpuskaniye.


Reserve course of a pedal

 PERFORMANCE ORDER

  1. At the started engine ask the assistant to squeeze out a pedal with effort about 49 kgfs and measure height of provision of a block of the squeezed-out pedal from a floor — do not forget to unbend a mat. At negative results of check drive away the car in a workshop of car service for performance of the corresponding adjustment.

Excessive lowering of a pedal can speak violation of adjustment of drum brake mechanisms of back wheels — try to cock and release the parking brake several times.


Height of provision of a pedal

 PERFORMANCE ORDER

  1. Measure height of provision (D) pedal of the parking brake lowered (N) and squeezed out (see an illustration Adjusting parameters of a pedal of a foot brake). compare results of measurement to requirements of Specifications. In case of need release a lock-nut and make necessary adjustment by rotation of a rod of a pusher of the brake amplifier. Having finished, tighten a nut with the required effort (16 — 22 Nanometers) — track that the tip of a rod remained in a cutting finger of a pusher.


"on the page back
9.11. Adjustment of the drive of the parking brake
on the following page"
9.13. Adjustment of a spring of the valve regulator (LSV), sensitive to loading