Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and steering of the car
10.3. Check of a state and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability
10:10. Replacement of stupichny bearings
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10:12. Removal and installation of components and assembly of a back suspension bracket
10:13. Removal, check of a state and installation of levers of a back suspension bracket
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket
10:15. Removal and installation of shock-absorbers of a back suspension bracket
10:16. Removal and installation of the back stabilizer of cross stability
10:17. Removal, check of a state and installation of a cross jet bar of a back suspension bracket
10:18. Pumping of a hydraulic path of the steering drive
10:19. Checks and adjustments of a steering wheel
10:20. Check of effort of resistance to sliding of a lath of the steering mechanism
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
10:22. Check of hydraulic pressure of GUR
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump
10:24. Removal and installation of reduktorny assembly
10:25. Removal and installation of assembly of the steering mechanism
10:26. Removal and installation of the steering pump
10:27. Removal and installation of a steering wheel
10:28. Removal and installation of assembly of the combined understeering switches
10:29. Removal and installation of the lock of ignition / blocking of a steering column
10:30. Removal, check of a state and installation of a steering column
10:31. Angles of installation of forward wheels
11. Body
12. Electric equipment
 














10-13-snyatie-proverka-sostoyaniya-i-ustanovka-rychagov-zadnejj-podveski.html

10:13. Removal, check of a state and installation of levers of a back suspension bracket

 PERFORMANCE ORDER

  1. Remove the lever which is subject to service (see Removal and installation of components and assembly of a back suspension bracket).
  2. Visually check assembly of the lever for existence of cracks, deformations and other mechanical damages.
  1. Estimate a condition of rubber-metal plugs, in case of need make their replacement — removal and installation of saylentblok is made by means of couple of special mandrels.

    A — Removal of the rubber-metal plug of the lever of a back suspension bracket
    B — Installation of the rubber-metal plug of the lever of a back suspension bracket

A.

B.

Before installation of a wall of the new plug it is necessary to grease with 1 percent water solution of soap.


Do not try to begin to knock the plug directly the hammer at all!

  1. At installation of levers pay attention to correctness of orientation of fixing bolts and nuts.
  1. Final tightening of fixture of the ends of levers equipped with rubber-metal plugs is made in the unloaded state at the wheels lowered on the earth.


"on the page back
10:12. Removal and installation of components and assembly of a back suspension bracket
on the following page"
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket