Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and steering of the car
10.3. Check of a state and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability
10:10. Replacement of stupichny bearings
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10:12. Removal and installation of components and assembly of a back suspension bracket
10:13. Removal, check of a state and installation of levers of a back suspension bracket
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket
10:15. Removal and installation of shock-absorbers of a back suspension bracket
10:16. Removal and installation of the back stabilizer of cross stability
10:17. Removal, check of a state and installation of a cross jet bar of a back suspension bracket
10:18. Pumping of a hydraulic path of the steering drive
10:19. Checks and adjustments of a steering wheel
10:20. Check of effort of resistance to sliding of a lath of the steering mechanism
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
10:22. Check of hydraulic pressure of GUR
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump
10:24. Removal and installation of reduktorny assembly
10:25. Removal and installation of assembly of the steering mechanism
10:26. Removal and installation of the steering pump
10:27. Removal and installation of a steering wheel
10:28. Removal and installation of assembly of the combined understeering switches
10:29. Removal and installation of the lock of ignition / blocking of a steering column
10:30. Removal, check of a state and installation of a steering column
10:31. Angles of installation of forward wheels
11. Body
12. Electric equipment
 














10-8-snyatie-i-ustanovka-stupichnojj-sborki-i-povorotnogo-kulaka.html

10.8. Removal and installation of stupichny assembly and rotary fist


Design of stupichny assembly of a forward wheel


Removal

 PERFORMANCE ORDER

  1. The car also establish to Poddomkratta it on props (see the illustration Scheme of an Institution of Props for fixing of the car in the lifted situation). Remove the corresponding forward wheel.
  2. Disconnect an electrical wiring from the wheel ABS sensor.
  3. Turn out fixing bolts, remove a support and tie up it a wire to suspension bracket elements (see the Head Podvesk and steering).
  4. Turn out fixing bolts and remove a driving flange.
  5. Easy percussions by the hammer with brass brisk release a pin of the external CV JOINT of a power shaft from a nave.
  6. Remove a lock washer.
  7. Having used a special stripper of KV40105400, turn off a nut of the stupichny bearing.
  8. Remove the external bearing and stupichny assembly.
  9. Give fastening bolts to a nave of a rotary fist.
  10. Remove the forelock of a tip of steering draft and give a shpilechny nut.
  11. By means of a stripper of ST9020001 separate a draft tip.


Installation

 PERFORMANCE ORDER

  1. Installation is made as it should be, the return to an order of dismantle of components. Do not forget to adjust properly stupichny bearings (see Adjustment of a pretightness of stupichny bearings of forward wheels). Track that were it is replaced all lock washers and sealing elements. Tighten all fixture with the required effort.


"on the page back
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
on the following page"
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability